taultunleashed

I'll try to keep these updated if Admin wants to sticky it.

The attached coordinates include:

• Jumping puzzles
• Points of interest
• Vistas
• Skill challenges
• Waypoints
• Renown hearts

This list shows how to sync the character after TP!

(Note: Using an ability to sync after TP is not necessary with other commercial teleport solutions such as Auto Explorer.)

• WARRIOR: Whirlwind Attack - Use a Greatsword and Savage Leap - Use a Main hand sword
• ELEMENTALIST: Burning Retreat - Use a Staff. (Thanks to luckysurfcs!) and Ride the Lightning or Updraft (Air) - Use a Dagger (Off-Hand)
• THIEVES: Flanking strike - Use double Dagger and Heartseeker - Use Dagger in Mainhand
• ENGINEER: Overcharged Shot - Use a Rifle
• GUARDIAN: Mighty Blow - Use a 2H Hammer / Leap of Faith and Symbol of Wrath- Use a Greatsword
• RANGER: Hornet Sting and Serpent's Strike - Use 1H Sword / Quick Shot - Use a Shortbow
• NECROMANCER: unknown.
• MESMER: Blurred Frenzy - Use a Main hand sword

This List shows how to sync the character in the WATER after TP!

• WARRIOR: Tsunami Slash - Use a Spear
• ELEMENTALIST: Tidal Wave (ice) - Use a Trident / Thanks, hateproject!
• THIEVES: Escape - Use a Harpoon Gun
• ENGINEER: Retreating Grapple - Use a Harpoon Gun
• GUARDIAN: Spear Wall - Usa a Spear
• RANGER: Ink Blast - Use a Harpoon Gun
• NECROMANCER: Foul Current - Use a Trident
• MESMER: unknown

If the coordinates are incorrect and the X,Y,Z are set to 500000, it's due to localization issues. For Windows 7, go to Control Panel -> Region and Language -> Additional Settings -> Change 'Decimal Symbol' to a comma, then close out everything and reload gZoom. IT will work properly after these steps.

Elementalist: Trident underwater Tidal wave (ice)

hey can u tell how its working please?

I loaded one of the coordinate , Lion Arch , and its apears me Pol 1 , pol 2 ; pol 3 etc .
but when I clik on pol 1 nothing happens, i need to write the XYZ then clik teleporte for all the coordinat?
or something automatic ?

tidusfrench wrote:hey can u tell how its working please?

I loaded one of the coordinate , Lion Arch , and its apears me Pol 1 , pol 2 ; pol 3 etc .
but when I clik on pol 1 nothing happens, i need to write the XYZ then clik teleporte for all the coordinat?
or something automatic ?

You just click or doubleclick the point you wish to go to. After that you press 'Teleport'. To sync your character you use the skills posted above in the OP.

Actually, you don't even need to use a skill. If you splash into water, or run into a wall/obstacle for just 1-2 secs, you will sync up really fast. Works for me, especially when I don't want to make any noise/use any skills to attract attention to my presence when I tele into a spot.

Hope this helps someone...

I wonder why it works differently for everyone. Is it internet connection? Water is actually bad for me. IF I come across water - It wont sync. It would even get stuck between the land/water skills so I have nothing in my bars usually.

Thanks for this great job!
Is there any chance to get WvW coordinates? thanks in advance

WHAT DOES SC AND RH STAND FOR PLZ HELP??

could you put the coords for worldvworld ??

What might I be doing wrong. When clicking the lines it either edit's the line or it puts the numbers in as 50000.0000 or -50000.000 and i get on the corner of the map when using your xyz's

ponk120 wrote:WHAT DOES SC AND RH STAND FOR PLZ HELP??

frigin wrote:What might I be doing wrong. When clicking the lines it either edit's the line or it puts the numbers in as 50000.0000 or -50000.000 and i get on the corner of the map when using your xyz's

Both questions are answered in the OP

good call ox thx i was totally blind

Has anyone figured out sync for the following?
Mesmer - water
Necro - land

even the skills listed doesnt work at times =( ex blurred frenzy for mesmer

new patch brake it?

could someone PM me with info on how to open the .xyz coordinate file? I can't seem to get it to work.