taultunleashed

1. This macro has two variations, the first is running this macro when your away from all craft stations. That means you will have to "GRIND" on your simple basic items, usually they only give about 100xp an item, but at the speed of this macro you can get approx 400x in 20 seconds that computes to 1200xp a minute, which is 72,000xp an hour. In my field (Bio Engineering) 72k xp is INCREDIBALE. Also your xp will vary depending on which item you are grinding. Secondly you can add lines (explained later) to craft next to crafting stations.
 
2. This macro is designed for use with 4 crafting kits. (you can adjust it once you get the hang of it)
 
3. YOU STILL HAVE TO MANUALLY ADD INGREDIANTS INTO SCHEMATIC SLOT. (so, its not an AFK macro, but it speeds up grinding BIG TIME).
 
4. CAPITALIZE EXACTLY THE SAME AS I DID (for example when you type in command toolbarSlot make sure you capitalize the "S")
 
Here we go:
 
1. Make two rows of hotkeys EMPTY. (you can fill up unused ones after your setup)
 
2. Place 4 craft kits in the LOWER hotbar spaces F5-F8.
 
3. Hit Ctr-A and click on create new MAcro.
 
4. First macro we are creating call it "ENDCRAFTING". Pick whatever image you want for it. Type this in command box EXACTLY:
/pause 8; /nextcraftingstage; /nextcraftingstage; /createPrototype practice no item; /createPrototype practice no item;
 
(if you want to run this macro not in practice mode then delete “practice no item” out of the commands. Also if you want to grind next to a craft station, then add another /nextcraftingstage; command directly after /pause 8;)
 
 
5. Once created place this macro in UPPER hotkey F9.
 
6. Next we are going to create the macro that will start the whole process. Call this macro "RUNCRAFTING". Choose any image. For commands type: /ui action toolbarSlot04; /pause 10; /ui action toolbarSlot05; /pause 10; /ui action toolbarSlot06; /pause 10; /ui action toolbarSlot07;
 
7. Place this macro in hotkey F1. (You will press this key to start the whole macroing process.)
 
8. Now we are going to create a series of 4 macros. Call them, CRAFTINGMACRO1, CRAFTINGMACRO2, CRAFTINGMACRO3, and CRAFTINGMACRO4. Choose any images for them. In command box for the first one you will type: /ui action toolbarSlot16; /selectDraftschematic 30; /ui action toolbarSlot08;
 
9. Once done place "CRAFTINGMACRO1" in UPPER hotbar slot F4. Then place "CRAFTINGMACRO2" in UPPER hotbar slot F5. Put "CRAFTINGMACRO3" in UPPER hotbar slot F6 and "CRAFTINGMACRO4" in UPPER hotbar slot F7.
 
10. When you create "CRAFTINGMACRO2" change the command /ui action toolbarSlot16 to say toolbarSlot17. Make craftingmacro3 to say 18 and craftingmacro4 to say 19.
 
11. NOW FOR THE HARD PART. Determine what you want to craft. Once you have that picked out you will need to change this command /selectDraftschematic 30; to whatever number your schematic is. For example, to make a plain tent. you may have have to put /select Draftschematic 13; EVERYBODY HAS DIFFERENT NUMBERS. The only way to find what number your schematic is that you are wanting to craft is by trial and error, keep chaning the number in the macro till it pops up the on you want. Keep in mind once you find this out CHANGE IT FOR ALL 4 "CRAFTINGMACROS".


Want to be a moderator and your already a member? Email us at Register to unlock hidden link

Ok i have a question there is no F1.... now so will that still work with the 1 2.... for the tolbar thanks

The interface used in space is still very similar to the PRE NGE interface.. Still has the F1-24 keys. As long as your piloting the ship at all times you can run the macro's.

I personally have tested and can confirm that pre-nge crafting macro's will work in space.


NOTE: Use a ship you can walk around on if you plan on making items.. So you can dump the items somewhere in your ship. If your just grinding, it makes no difference. (MUST BE DONE WHILE IN PILOTS SEAT)

would putting a crafting station in a droid let you do some of the other combines in space?